Uses

  •  Prototyping and validation of custom ASIC IP alongside an Arm processor in silicon in Juno
  • Base hardware for a Soft Macro Models (SMM)

The LogicTile Express 20MG is the recommended choice for FPGA expansion with the Juno Arm Development Platform.

.

 

Specifications


LogicTile Express 20MG
LogicTile name (short) V2F-1XV7 or LTE-20MG
Part number V2F-1XV7-0313A
PCB number HBI-0247
Datasheet Datasheet
Manuals User Guide
FPGA Family Virtex 7
FPGA XC7V2000T / XC7V2000T-CES
ZBT RAM N/A
SDRAM 4GB DDR3 SODIMM (included)
Programmable Clocks 6
User Switches 8 DIP switches
User LEDs 9
PCIe connectivity 4 Rx/Tx lanes up, 4 Rx/Tx lanes down
SATA connectors Host + Device, 2×Rx/Tx lanes each
HSSTP connector N/A
Further upward IO 440 single-ended signals (HDRX/Y)
Stackable with other LTE Yes, up to 8 LTE-20MG boards
Power supply From motherboard + 12V DC PCIe
Expansion boards HDMI IO board


 

Get support

Community Forums

Suggested answer Can't download code to address 0 on STM32F091RC using uVision 0 votes 173 views 2 replies Latest 9 hours ago by Westonsupermare Pier Answer this
Not answered Include source file in DS 2020 0 votes 33 views 0 replies Started 14 hours ago by Brittany_ruth Answer this
Not answered communication 0 votes 55 views 0 replies Started 22 hours ago by jishan33333 Answer this
Not answered target not created error + Debug not responding 0 votes 64 views 0 replies Started yesterday by PShrestha Answer this
Suggested answer STM32, Keil + first steps in astrology?
  • Microcontroller (MCU)
0 votes 350 views 3 replies Latest yesterday by Andy Neil Answer this
Not answered Creating an Assembly project in DS IDE 2020 1 votes 217 views 0 replies Started 2 days ago by Brittany_ruth Answer this
Answered osMutexWait() function before the RTX osKernelInitialize() 0 votes 414 views 9 replies Latest 2 days ago by Andy Neil Answer this
Answered Code jumps to cxsync1 in vectors.S?
  • Arm Development Studio
0 votes 639 views 2 replies Latest 2 days ago by DanijelDomazet Answer this
Not answered Help to develop GUI personal from command line BlueNRG-2 and STLINK-V3 0 votes 84 views 0 replies Started 3 days ago by Pathros Answer this
Suggested answer Can't download code to address 0 on STM32F091RC using uVision Latest 9 hours ago by Westonsupermare Pier 2 replies 173 views
Not answered Include source file in DS 2020 Started 14 hours ago by Brittany_ruth 0 replies 33 views
Not answered communication Started 22 hours ago by jishan33333 0 replies 55 views
Not answered target not created error + Debug not responding Started yesterday by PShrestha 0 replies 64 views
Suggested answer STM32, Keil + first steps in astrology? Latest yesterday by Andy Neil 3 replies 350 views
Not answered Creating an Assembly project in DS IDE 2020 Started 2 days ago by Brittany_ruth 0 replies 217 views
Answered osMutexWait() function before the RTX osKernelInitialize() Latest 2 days ago by Andy Neil 9 replies 414 views
Answered Code jumps to cxsync1 in vectors.S? Latest 2 days ago by DanijelDomazet 2 replies 639 views
Not answered Help to develop GUI personal from command line BlueNRG-2 and STLINK-V3 Started 3 days ago by Pathros 0 replies 84 views